Top 9 Stealth Vacuum Kit

The new Stealth Brush has improvements including a new short cord that plugs into the all new Stealth Wand. The old style Stealth had a 40″ cord that ran up the metal wands. The new one handsomely integrates the cord into the telescopic wand. Stealth is now ONLY AVAILABLE with its new wand. Upgrading an older system? A compatible hose is all that is necessary. The Electric Hose from M.D. Manufacturing, Inc. will fit, as well as all older Stealth, Ace, EdgeLift, BlackHawk, most Nutone, and others. If there are two inches between the button lock nipple on the hose end and the two holes where the pins go into the hose handle, the new Stealth with Wands will fit perfectly.

Cen-Tec’s 93642 is designed to provide the cleaning accessories most often requested in a low voltage central vacuum hard floor and general-purpose attachment set. The 1.375” x 35 foot hose is longer than the industry standard 30 feet to insure you reach everywhere in your home. A hose with an inner diameter of 1.375” insures superior airflow and improved cleaning performance that also assists the performance of air turbine tools often used with low voltage hoses. Further, the hose allows for switch control to turn the central vacuum on and off at the handle. A 12” natural fill floor brush and fully automatic combination nozzle address hard surfaces, area rugs, and even carpeted surfaces. A premium chrome ratchet telescopic wand with the easy release button down feature and a full set of premium above the floor accessories address upholstery, stairs, table tops, crevices, and baseboards. The tool caddy clip lets them travel with you while you clean. The 93642 is compatible with all major brands of central vacuum including Eureka, Beam, Electrolux, Hoover, Cyclovac, Vacuflo, Vacumaid, MD, M&S, Husky, Canavac, Honeywell, and well as most regional brands.

The 93070 kit has a two position on off switch hose which creates a Circuit through the two low voltage electrical contacts in your inlet valve. You will see the wall end has a two metal contact Plates separated by a thin plastic landing. These Plates create the Circuit through the switch in the hose handle that permits control of your central vacuum. There is a small tab projecting from the top of the hose end that helps you orient the hose in your inlet. This tab should be located at the top of the inlet valve opening as you insert the hose end. The wave combination nozzle is designed to move from carpets to hard floor without the need to make an adjustment. There is a simple friction connection between the floor nozzles and the end of the telescopic wand to make changing tools easier. The wand ratchets at one inch intervals from 25 to 42 inches so you can adjust to a height comfortable for your use. Many find the 93070 an ideal second package to complement their electric brush kit for the portion of the home dominated by hard floor surfaces like the kitchen, family room, den, or basement. An Italian made ratchet chrome telescopic wand with nylon collar and a full set of soft vinyl accessories are ideal for cleaning above the floor. The accessories include a 5 inch natural fill dusting tool, a 13 inch vented crevice tool, and 5 inch upholstery tool with a built in brush strip ideal for stairs and the sofa, a mesh caddy bag collects everything between uses and the mesh allows you to easily see the tool you need through the bag.

The 91431 is designed to be a general use straight air accessory set for the home, shop, or garage. Often it is used as a second tool set Complimenting the power nozzle or Turbine package that came with the central vacuum. Having a second tool set can save you time and effort moving a tool set from floor to floor in multi-story homes. The hose end is designed for what has historically been industry standard inlets and will activate a system with low voltage contacts in the wall valve. There were a few valves typically produced before 1980 which may use a micro-switch for activation of the vacuum. In most cases the 91431 will still work but the automatic activation of the system will not be delivered by the banded cuff. The set includes a full range attachments for most standard household cleaning jobs. This set is deal for a basement, garage, or general use in the home, especially on hard floor areas. The floor brush is ideal for cleaning hardwood, tile, stone, and vinyl.

The 92938 central vacuum accessory package is designed to provide superior cleaning for today’s home with a mix of both carpeted and hard floor surfaces. The power nozzle is designed to provide the three features most sought in cleaning. Excellent deep down dirt recovery, excellent Grooming of the carpeted surface, and superior edge cleaning. The life-time reinforced poly-V belt will provide years of reliable service without the need to routinely Replace the Drive belt. The 35 foot total control hose is the longest permitted by UL/CSA standard so you are sure to reach all areas of your home. Customers most often request a hose Sock to protect the investment in their home and furnishings. We have recognized this by pre-installing a premium Sock treated with an anti-microbial to protect you and your home environment. The direct connect end makes the system compatible with all major brands of industry standard high volt and low volt electrified inlet valves. By connecting to all major brands of electrified inlets the 92938 is compatible with all major brands of central vacuums with these inlets including beam, ELECTROLUX, eureka, Nutone, VacuMaid, Vacuflo, husky, Canavac, Cyclovac, Md and imperium brands. A 35 foot crush proof total control hose lets you turn your central vacuum on and off from the hose handle independent of the power nozzle ideal for cleaning hard floor surfaces. The three position switch also allows you to also control power to electric nozzle and the vacuum when cleaning carpeted surfaces. A soft anti-microbial treated cotton-lycra blend hose Sock is installed on the hose to protect for surfaces, furnishings, and walls from the corrugation of the hose. The hose has a direct connect end combining the high voltage pin jack in conjunction with the low voltage contacts permitting control of both the vacuum unit and the electric power nozzle. The 14 inch wide power nozzle has a chevron agitator design shown to provide superior cleaning performance.

The 93367 is designed to complement all major central vacuum systems and is an ideal set of accessories for those concerned about black tools marking surfaces. The 1.25 inch inner diameter commercial grade vacuum hose is highly flexible with a smooth interior for superior airflow. Cen-Tec’s trademarked arc relax strain relief system covers the last 14 inches of each end of the hose and prevents kinking increasing hose life. The premium combination nozzle has a wheel system, metal base plate, and pivoting swivel neck that keeps the tool parallel to the surface of the floor for superior vacuuming. A five-piece accessory set with natural fill dusting and natural fill upholstery tool is ideal for all above the floor surfaces. The 93367 is lightweight, making it ideal for cleaning above the floor surfaces, stair risers, while reducing fatigue. The 93367 is designed to be compatible with all major central vacuum brands including: Beam, Electrolux, Eureka, Vacumaid, Vacuflo, MD, Cyclovac, Canavac, Honeywell, Galaxie, Imperium, and Nutone installed with valves that have approximately a 1.50 inch industry standard opening.

The 92718 kit has a two position on off switch hose which creates a circuit through the two low voltage electrical contacts in your inlet valve. You will see the wall end has a two metal contact plates separated by a thin plastic landing. These plates create the circuit through the switch in the hose handle that permits control of your central vacuum. There is a small tab projecting from the top of the hose end that helps you orient the hose in your inlet. This tab should be located at the top of the inlet valve opening as you insert the hose end. The wave combination nozzle is designed to move from carpets to hard floor without the need to make an adjustment. There is a simple friction connection between the floor nozzles and the end of the telescopic wand to make changing tools easier. The wand ratchets at one inch intervals from 25 to 42 inches so you can adjust to a height comfortable for your use. Many find the 92718 an ideal second package to complement their electric brush kit for the portion of the home dominated by hard floor surfaces like the kitchen, family room, den, or basement.